Leading 10 common forklift accidents ， forklift operation should pay attention to these matters ！.

Do not underestimate the forklift at the office. If the procedure is bad, there will certainly be significant crashes in mins, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the balance of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the route and holds on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was squashed.
Forklift procedure ought to take notice of these matters ：.

Start.
1. Prior to starting, observe the surroundings, and after verifying that there are no obstacles that prevent the security of driving, beep the horn initially and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork ought to be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the lorry to shed lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to obey the traffic rules in the factory and must keep a certain security distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be elevated other than when piling or packing. .
8. The height of the load must not block the driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

filling and discharging.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing ought to protest the rack. .
2. It is restricted to deal with a single fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The speed of the vehicle must be slow and consistent. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the tons, and it needs to be noted that the fork idea should not touch other items or objects. The tons needs to be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll objects. .
10. It is not allowed to utilize forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance should be checked, and gas, lubing oil and air conditioning water ought to be included.
2. Check the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you Electric Forklift Truck for Warehouse encounter a person Stand-on Electric Pallet Stacker before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope must be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they ought to take the turning around exercise
.
The "Eight Prohibitions" should be adhered to in the operation.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to use stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring people to deal with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the contrary side of the area with the very same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844